LSI MegaRAID SCSI 320-2 RAID Controller Series 518 Manuel d'utilisateur Page 120
- Page / 158
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
7-26 Installing and Configuring Clusters
Copyright © 2002 by LSI Logic Corporation. All rights reserved.
Installation of Cluster Service on the second node takes less time than
on the first node. Setup configures the Cluster Service network settings
on the second node based on the configuration of the first node.
Installation of Cluster Service on the second node begins the same way
as installation on the first node. The first node must be running during
installation of the second node.
Follow the same procedures used to install Cluster Service on the first
node, with the following differences:
1. In the Create or Join a Cluster dialog box, select The second or
next node in the cluster, then click Next.
2. Enter the cluster name that was previously created (it is MyCluster
in this example), and click Next.
3. Leave Connect to cluster as unchecked. The Cluster Service
Configuration Wizard automatically supplies the name of the user
account selected when you installed the first node. Always use the
same account you used when you set up the first cluster node.
4. Enter the password for the account (if there is one), then click Next.
5. At the next dialog box, click Finish to complete configuration.
The Cluster Service will start.
6. Click OK.
7. Close Add/Remove Programs.
8. If you install additional nodes, repeat the preceding steps to install
Cluster Service on all other nodes.
7.4.18 Verifying Installation
There are several ways to verify that Cluster Service was successfully
installed. Here is a simple one:
1. Click Start, click Programs, click Administrative Tools, then click
Cluster Administrator.
The presence of two nodes (pictured below) shows that a cluster
exists and is in operation.
- MegaRAID 1
- SCSI 320-2 1
- RAID Controller 1
- HARDWARE 1
- FCC Regulatory Statement 3
- Logical Drive Configuration 8
- Physical Device Layout 10
- Contents 15
- Contents xvii 17
- Contents xix 19
- Chapter 1 21
- Overview 21
- 1.2 NVRAM and Flash ROM 22
- 1.3 SCSI Connectors 22
- 1.7 Documentation 23
- • MegaRAID Manager 24
- • Power Console Plus 24
- Chapter 2 25
- Introduction to RAID 25
- 2.1.2 Increased Reliability 26
- 2.2.1 Host-Based RAID 26
- 2.3 RAID Overview 27
- 2.3.3 Consistency Check 28
- 2.3.4 Fault Tolerance 28
- 2.3.5 Disk Striping 28
- RAID Overview 2-5 29
- MegaRAID Controller 29
- 2.3.6 Disk Mirroring 30
- 2.3.7 Disk Spanning 31
- 2.3.8 Parity 32
- 2.3.9 Hot Spares 32
- 2.3.10 Hot Swapping 33
- 2.3.11 Disk Rebuild 33
- 2.3.12 Logical Drive States 34
- 2.3.13 SCSI Drive States 34
- 2.3.14 Disk Array Types 35
- 2.3.15 Enclosure Management 35
- 2-12 Introduction to RAID 36
- Chapter 3 37
- RAID Levels 37
- 3.2 RAID 0 38
- 3.3 RAID 1 39
- 3.4 RAID 5 40
- Figure 3.3 RAID 5 Array 41
- 3.5 RAID 10 42
- 3.6 RAID 50 43
- Figure 3.5 RAID 50 Array 44
- Chapter 4 45
- Features 45
- 4-2 Features 46
- 4.1 SMART Technology 47
- 4.2 Configuration on Disk 47
- 4.3 Configuration Features 47
- 4.5 RAID Management Features 49
- 4.6 Fault Tolerance Features 50
- 4.7 Software Utilities 50
- 4.10 MegaRAID Components 52
- 4.10.2 Cache Memory 53
- 4.10.3 MegaRAID BIOS 53
- 4.10.4 Onboard Speaker 53
- 4.10.5 Serial Port 53
- 4.10.6 SCSI Bus 54
- 4.10.7 SCSI Connectors 54
- 4.10.8 SCSI Termination 54
- 4.10.9 SCSI Firmware 54
- 4.11 RAID Management 55
- 4.12 Compatibility 56
- Chapter 5 57
- Configuring Physical Drives 57
- Arrays, and Logical Drives 57
- 5.1.5 Physical Device Layout 62
- 5.2 Configuring Arrays 65
- 5.3 Creating Logical Drives 66
- 5.3.2 Assigning RAID Levels 68
- 5.4 Configuring Logical Drives 69
- Chapter 6 73
- Hardware Installation 73
- 6.2 Installation Steps 74
- 6.2.1 Step 1: Unpack 75
- 6.2.2 Step 2: Power Down 75
- 6-4 Hardware Installation 76
- 6-6 Hardware Installation 78
- 6.2.5 Step 5: Set Termination 80
- Installation Steps 6-9 81
- 6-10 Hardware Installation 82
- Installation Steps 6-11 83
- • Tape drive set to SCSI ID 2 84
- Installation Steps 6-13 85
- Installation Steps 6-15 87
- 6-16 Hardware Installation 88
- Installation Steps 6-17 89
- 6-18 Hardware Installation 90
- 6.2.11 Step 11: Power Up 92
- 6.3 Summary 93
- 6-22 Hardware Installation 94
- Chapter 7 95
- Installing and Configuring 95
- Clusters 95
- 7.2 Benefits of Clusters 96
- Advanced Server 97
- 7.3.2 Network Requirements 98
- 7.4 Cluster Installation 99
- • Set up networks 100
- • Set up disks 100
- 7.4.3 Setting Up Networks 101
- Cluster Installation 7-9 103
- Cluster Installation 7-13 107
- Cluster Installation 7-15 109
- Cluster Installation 7-17 111
- Cluster Installation 7-19 113
- Cluster Installation 7-21 115
- Cluster Installation 7-23 117
- Cluster Installation 7-25 119
- 7.4.18 Verifying Installation 120
- 7.5 Installing SCSI Drives 121
- Chapter 8 123
- Troubleshooting 123
- Firmware Initializing 124
- 8.2 BIOS Boot Error Messages 125
- 8.3 Other BIOS Error Messages 127
- 8.4 Other Potential Problems 127
- 8-8 Troubleshooting 130
- Appendix A 131
- SCSI Cables and 131
- Connectors 131
- SCSI devices is shown below 133
- Table A.1 SCSI Cable Vendors 136
- Appendix B 141
- Audible Warnings 141
- B-2 Audible Warnings 142
- Appendix C 143
- Glossary 143
- C-2 Glossary 144
- C-4 Glossary 146
- C-6 Glossary 148
- C-8 Glossary 150
- C-10 Glossary 152
- IX-2 Index 154
- Index IX-3 155
- IX-4 Index 156
- Customer Feedback 157
Produits connexes et manuels pour Contrôleurs périphériques LSI MegaRAID SCSI 320-2 RAID Controller Series 518
(3 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.067 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels